Name: The Quick Zip - Replacement Zipper Heads
Brand: Notting Hill Equine ®
SKU: CJYD209083927AZ
Price: 14.99 USD
Availability: InStock

The Quick Zip - Replacement Zipper Heads

18 Piece Set

$14.99

The Quick Zip - Replacement Zipper Heads

$14.99

Shipping calculated at checkout.

When the pull pops off a tall boot, the zipper itself is usually fine. The slider has worn loose or come away from the teeth, and the standard fix at a cobbler is to cut out and restitch the entire zipper. The Quick Zip replaces just the slider. Loosen the thumbscrew, set it over the teeth, tighten it by hand, and the zipper runs again. No sewing, no tools, no week without your boots.

Each slider comes with its own cord pull and a soft, grippy tab that's easy to find with gloves on. The set covers small, medium and large zipper widths, so one kit handles field boots, paddock boots, half chaps, jackets and tack bags. Keep a few in the trunk and the next broken pull becomes a two-minute fix in the barn aisle rather than the end of a lesson.

It works when the teeth and the tape (the fabric strip the teeth are sewn into) are intact. If teeth are missing, or the zipper has torn away from the boot, the zipper itself needs replacing.

Replaces a lost, broken or loose zipper slider
Fits by hand with a metal thumbscrew, no sewing or tools
Cord pull with a soft, textured tab
Small, medium and large sizes
For tall boots, paddock boots, half chaps, outerwear and bags
6-piece set (two of each size) or 18-piece set

Questions

Will this fix my boot zipper?
If the slider came off, cracked, or stopped closing the teeth behind it, in most cases yes. If teeth are missing or the zipper has pulled away from the boot's seam, no. That needs a full zipper replacement from a cobbler.

Which size do I need?
Match the slider to the width of your zipper's teeth. The right size sits snugly over both rows and closes them evenly as you pull it. If one feels loose once tightened, try the next size down.

How do I fit it?
Loosen the thumbscrew so the slider opens. Set it over both rows of teeth near the bottom of the zipper, tighten the thumbscrew firmly by hand, then run it up and down a few times to make sure it closes evenly.

Can I take it off again?
Yes. Loosen the thumbscrew and lift it off, which makes it easy to move to another zipper or swap to a better-fitting size.

Which set should I get?
The 6-piece set covers a single repair with spares in every size. The 18-piece set is the one for a tack trunk or a barn with several riders, and it works out to far less per slider.

Before fitting, brush any arena sand, mud or hair out of the zipper teeth, since grit is the most common reason a slider jams or wears loose. Tighten the thumbscrew firmly by hand, without forcing it, then run the slider up and down a few times to seat it. Check the thumbscrew now and then and retighten if it has worked loose. If the zipper feels stiff, rub a little beeswax, paraffin or a graphite pencil along the teeth. Wipe the slider dry after wet rides and keep spares in their bag, somewhere dry in the tack trunk, until you need them.

A hand-fitted replacement slider for a zipper whose original pull has come off, cracked or stopped closing. Each slider opens and closes with a knurled metal thumbscrew, so it fits over the existing teeth and tightens by hand, with no sewing and no tools, and can be loosened again to remove or move it. A cord pull with a soft, textured tab gives a sure grip, even in gloves. Black finish, in small, medium and large sizes to match different tooth widths, so one set covers tall boots, paddock boots, half chaps, outerwear and bags. Sold as a 6-piece set (two of each size) or an 18-piece set. Designed for zippers with intact teeth and tape; it does not replace missing teeth or repair a zipper torn from its seam.